by Kim Connors
Services
Products
Materials

1 - Silver-Plated 15x8mm Lobster Clasp #2642

49 - Silver-Plated Ball Pins #8355

59 - Silver-Plated 5mm 19 Gauge Jump Rings #1710

13 – Crystal AB 8x5mm Glass Crystal Rondelles #2244

12 – Light Gold AB 8x5mm Glass Crystal Rondelles #2241

12 – Red Topaz AB 8x5mm Glass Crystal Rondelles #2264

12 – Red AB 8x5mm Glass Crystal Rondelles #2239
Step 1 – Create the Drops
Crystal AB Rondelle Drop (13) – Add 1 – Crystal AB Crystal Rondelle to a ball pin.  Make a 90° bend in ball pin above the beads.  Using round nose pliers (or any pliers you have) hold the ball pin near the angle and bend it around the pliers to make a loop.  Wrap down around ball pin creating as many coils as you can.  Trim any extra.  Repeat 12 times.


Light Gold AB Rondelle Drop (12) – Add 1 – Light Gold AB Crystal Rondelle to a ball pin.  Make a 90° bend in ball pin above the beads.  Using round nose pliers (or any pliers you have) hold the ball pin near the angle and bend it around the pliers to make a loop.  Wrap down around ball pin creating as many coils as you can.  Trim any extra.  Repeat 11 times.


Red Topaz AB Rondelle Drop (12) – Add 1 – Red Topaz AB Crystal Rondelle to a ball pin.  Make a 90° bend in ball pin above the beads.  Using round nose pliers (or any pliers you have) hold the ball pin near the angle and bend it around the pliers to make a loop.  Wrap down around ball pin creating as many coils as you can.  Trim any extra.  Repeat 11 times.


Red AB Rondelle Drop (12) – Add 1 – Red AB Crystal Rondelle to a ball pin.  Make a 90° bend in ball pin above the beads.  Using round nose pliers (or any pliers you have) hold the ball pin near the angle and bend it around the pliers to make a loop.  Wrap down around ball pin creating as many coils as you can.  Trim any extra.  Repeat 11 times.

Step 2 – Assemble the Bracelet
1. Open one 5mm jump ring and add the loop of the lobster clasp.  Close the jump ring.






2. Open one 5mm jump ring, add TWO Crystal AB Rondelle Drops and the 5mm jump ring you added in Step 1. Close the jump ring.










3. Open one 5mm jump ring and add the 5mm jump ring you added in Step 2 between the Crystal AB Rondelle Drops.  Close the jump ring.










4. Open one 5mm jump ring, add TWO Light Gold AB Rondelle Drops and the 5mm jump ring you added in Step 3.  Close the jump ring.










5. Open one 5mm jump ring, and add the 5mm jump ring you added in Step 4 between the Light Gold Rondelle Drops.  Close the jump ring.










6. Open one 5mm jump ring, add TWO Red Topaz AB Rondelle Drops and the 5mm jump ring you added in Step 5.  Close the jump ring.











7. Open one 5mm jump ring and add the 5mm jump ring you added in Step 6 between the Red Topaz AB Rondelle Drops.  Close the jump ring.











8.  Open one 5mm jump ring, add TWO Red AB Rondelle Drops and the 5mm jump ring you added in Step 7.  Close the jump ring.










9. Open one 5mm jump ring add the 5mm jump ring you added in Step 8 between the Red AB Rondelle Drops.  Close the jump ring.

10. Continue the pattern in Steps 2-9 until you have used all 12 Red AB Rondelle Drops.

11. Open one 5mm jump ring and add the last 5mm jump ring with the Red AB Rondelle Drops, between the Drops.  Close the jump ring.










12. Open one 5mm jump ring and add the 5mm jump ring from Step 11.  Close the jump ring.

13. Continue adding 5mm jump rings until you have a total of 10 empty jump rings after the two Red AB Rondelle Drops.


14. Open one 5mm jump ring, add ONE Crystal AB Rondelle Drop and the last 5mm jump ring from Step 13.  Close the jump ring.













You are done!!  These instructions make a bracelet that is adjustable up to 8 ½ inches long.  Just attached the lobster clasp to the jump ring that is the right fit for you!!